As a value pack the cost is greatly reduced making it a great buy for students. Inspect exhaust system for leaks; check hangers, brackets, and heat shields; determine needed repairs. Each answer in the Practice Test has clear explanations of why the right answer was the correct choice. Technician B is correct because the first step in a leaking fluid line fitting is to tighten it to specifications using a torque wrench. The heat is actually enough to cause oil to boil and its temperature can reach near 1,100 Fahrenheit.
Once you finish mechanic school and get a few years of experience under your belt, finding a great is at the forefront of your mind. Inspect axle housing and vent; inspect rear axle mountings. Technician B says that if the automatic transmission oil cooler lines are found to be leaking, they are first tightened to specifications. When the bulb is turned on, it begins to get hot. Inspect transfer case, front differential, and axle seals and vents.
Keep up the good work! The G1 test prep manual contains Test Specifications, a task list, and sample questions with answers. This is even more pronounced when the vehicle is at rest. Verify operation of engine-related warning indicators. Suspension and Steering 13 questions 1. There are more than 40 categories in which you can earn this status, encompassing all areas of automotive diagnosis, maintenance, and repair.
This certification seeks to identify and recognize those Maintenance and Light Repair Technicians who can demonstrate knowledge of the skills necessary to successfully perform the most common maintenance and light repair tasks. Much of this heat is dumped into air around the bulb and is carried away. This is because the right front brake unit has more stopping power. Verify instrument panel lamps operation; conduct relearn procedure. Perform starter current draw test; interpret readings.
Replace fluid and filter s. The unscored questions are not differentiated from the rest, so you will need to answer every question on the test to the best of your ability. The timer on the computer screen will show the amount of time left. However, when there is oil on the bulb, it begins to get heated as well. Road test the vehicle to verify drive train noises and vibration. Repair the system and flush with fresh brake fluid C.
Instructors: Jim is sure you'll find the information included in this website useful in your classroom. This sample test has 152 questions and explanations. Website designed, developed, hosted, and maintained by. Inspect front strut cartridge or assembly. Inspect rear strut cartridge or assembly, and upper mount assembly.
Inspect and replace front stabilizer bar sway bar bushings, brackets, and links. Inspect, adjust, and repair transfer case manual shifting mechanisms, bushings, mounts, levers, and brackets. Please be sure to contact to request his textbooks for your next classroom order. Technician A is correct because heavy duty applications will use an auxiliary automatic transmission oil cooler. A restricted left front brake line will cause the vehicle to pull to the right when braking. C A stuck valve or engine misfire.
Identify front suspension system noises, handling, ride height, and ride quality concerns; disable air suspension system. We support: 145 Golfwood Dr. Inspect front wheel bearings, seals, and hubs. Debris on the condenser's fins reduces it's ability to transfer heat. Test parking brake indicator light, switch, and wiring. Check and adjust tire air pressure. The technician noticed that the vehicle has some play in the lift-side inner tie-rod.
Inspect, service, and replace wheel bearings, seals, and hubs, excluding press-type bearings. Perform battery tests load and capacitance ; determine needed service. After studying this guide, you should you should be well prepared to take the test. Inspect, adjust, and replace power steering pump belt s , tensioners and pulleys; verify pulley alignment. Inspect and test coolant; drain, flush, and refill cooling system with recommended coolant; bleed air as required. Includes 128 symbols and their meanings. Visually inspect condition of transmission cooling system, lines, and fittings.
Select, handle, store, and install proper brake fluids. Your test appointment will begin with a short video to familiarize you with our computer-based testing system. It is not a problem that will affect alignment. Perform pre-alignment inspection; prepare vehicle for alignment, and perform initial wheel alignment measurements. Engine Systems 9 questions 1. Inspect and replace crankcase ventilation system components.