Crown cts 2000 manual. Answered Crown CTs 2000 2Channel Amplifier Questions & Issues 2019-01-21

crown cts 2000 manual

Crown Cts 2000 Repair

crown cts 2000 manual

Operation normal mode Pressing the Channel A or Channel B button will immediately switch the input to that channel; the speaker indicator lights will indicate what speakers are connected. Common - leads to common terminal. Check for loads less than 2 ohms, and for excessive input levels. Mise à la terre du haut-parleur B. If 70 Vrms operation is desired, remove the wire leading to the speaker from the terminal marked 25V and connect it to the terminal marked 70 V. Reinstall the housing cover and retest. Commands entered via the telephone key pad allow the user to send a message to specified zones.

Next

CROWN CTS 2000 Amplifier

crown cts 2000 manual

They are suitable for use in areas with high ambient noise levels. Provide a copy of these instructions for the Safety Engineer, system operator s and maintenance personnel. En este momento se deberá brindar una breve explicación del servicio solicitado o de la naturaleza del malfuncionamiento. Be sure the neoprene rubber cover gasket is properly seated in the housing groove andreinstall housing cover. El exterior de este dispositivo tiene un acabado con duradera pintura a prueba de intemperie y todas las piezas metálicas han sido tropicalizadas para lograr una mayor resistencia a condiciones de gran humedad y al ataque de los hongos. The selection of the mounting location for the device, its controls and routing of the wiring is to be accomplished under the direction of the Facilities Engineer and the Safety Engineer. Son ideales para usar en áreas con un alto nivel de ruido.

Next

CROWN CTS 2000 Amplifier

crown cts 2000 manual

At this time a brief explanation of the service requested or the nature of the malfunction, should be given. Adequate hearing protection should be worn if standing within close proximity to the device while testing. Connect the 70 Vrms line at the terminals of Zone 1 Ð Zone 8 terminal block s. A can be obtained from the local Distributor or ManufacturerÕs Representative. Mueva el conjunto receptáculo-alambrepara fijar el nivel de salida deseado. Reinstall the housing cover and retest. Corriente 8 watt 15 watt Tableau 1.

Next

Answered Crown CTs 2000 2Channel Amplifier Questions & Issues

crown cts 2000 manual

Do not attempt to disable this ground connection by using an adapter or other methods. The selection of the mounting location for the device, its controls and routing of the wiring is to be accomplished under the direction of the Facilities Engineer and the Safety Engineer. Provide a copy of these instructions for the Safety Engineer s , System Operators s and Maintenance personal. ¥ Une fois que les essais sont terminŽs, donnez une copie de cette feuille d'instructions ˆ tous les employŽs de service. The selection of the mounting location for the device, its controls and routing of the wiring is to be accomplished under the direction of the Facilities Engineer and the Safety Engineer.

Next

Crown Audio CTs 600 : Operation Manual Power Amplifier CTs 600, CTs 1200, CTs 2000, CTs 3000

crown cts 2000 manual

Les tests devraient être effectués périodiquement. Secure the unit to the mounting surface with 10 screws appropriate for the type of mounting surface material. Asegúrese de que el empaque de neopreno de la caja está bien colocado en la ranura de la caja y reinstale la tapa de la caja. Expected tolerances are: Potentiometer steps 0-6dB: ± 1 dB Potentiometer steps 6-12dB: ± 1. ¥ Coupez l'ŽlectricitŽ avant de connecter ou de faire l'entretien de ce dispositif. C las Conexiones Eléctricas que se listan abajo y haga todas las conecciones eléctricas necesarias.

Next

Answered Crown CTs 2000 2Channel Amplifier Questions & Issues

crown cts 2000 manual

Turn down the level of your audio source. We also recommend recording the serial number and model before shipping for your reference. The speaker projector is adjustable and may be repositioned to obtain desired sound distribution. Connectez le fil audio positif + au terminal avec l'indicateur rouge. Refer to figures 2and 3. Common - leads to common terminal.

Next

Answered Crown CTs 2000 2Channel Amplifier Questions & Issues Page 13

crown cts 2000 manual

Todo el cableado debe hacerse a través de conduit y accesorios aprobados. We also recommend that you save all packing materials so you will have them if you ever need to transport the unit. Electrical Connections belowand make the necessary electrical connections. El parlante puede ser montado en una superficie relativamente plana. Input Impedance nominal : 10 kilohms balanced, 5 kilohms unbalanced.

Next

CROWN CTS 2000 OPERATION MANUAL Pdf Download.

crown cts 2000 manual

Multiple power settings are achieved via selection of transformer tabs. It utilizes a space of 1U. En ese momento se le pedirá una breve explicación del servicio solicitado o la naturaleza del desperfecto. Rejilla de acero cubierto de polvo blanco Para evitar un choque eléctrico, no intente instalar cables cuando está encendido. After unpacking the unit , examine it for damage that may have occurred intransit.

Next

Crown CTs 2000 Amplifier Specifications PDF View/Download

crown cts 2000 manual

File a claim immediately with the carrier stating the extent of the damage. Pour éviter des chocs électriques, ne connectez pas les fils si les circuits sont sous tension. Il est important de lire, comprendre et suivre toutes les instructions expédiées avec ce produit. The wire must be severed to provide electrical supervision of the connection. Usually this means that the amplifier must be serviced.

Next

CROWN CTS 2000 OPERATION MANUAL Pdf Download.

crown cts 2000 manual

Asegúrese de que el empaque de neopreno de la caja está bien colocado en la ranura de la caja y reinstale la tapa de la caja. Before use, your amplifier first must be configured for proper operation, including input and output wiring hookup. They are suitable for use in areas with high ambient noise levels. B 400 Printed in U. Check for proper ventilation and proper mode-switchsetting.

Next